Toilet partitions need to be cleaned, too, so before you buy toilet partitions, you need to know which cleaning material will suit your partition material. Toilet partitions have different materials, so one cleaning product may not be the best option for all partitions. But you don’t need to worry since we’ll help you.
To clean a toilet partition, you need to understand the type of material your partitions are made of. Are they built with solid plastic? Laminate or phenolic, or any other material? Are they built with stainless steel? You just need to use a warm mixture of water and mild detergent to clean them. Continue reading this post to know how you can remove and clean the scratches from different types of partitions.
Types of toilet partitions and how to clean them
Solid plastic partitions
Solid plastic is among the most commonly used toilet partition material. That’s because they’re easy to clean. After all, they’re resistant to rust and water. Use a warmed spoon with pressure so you can eradicate scratches from a solid plastic material. Then, you rub and stroke the spoon over the scratch so you can eliminate the scratches.
To avoid scratches, make sure to abstain from using steel fleece from cleaning. For a portion of those harder stains that delicate cleaners can’t help, use a non-grating industrial cleaner. You can also blend a DIY cleaner by mixing the things below:
- 1 gallon of water
- ½ cup of regular detergent
- 66% trisodium phosphate in a cup
Plastic laminate partitions
Plastic laminate toilet partitions are made from a molecule board and are covered with a plastic laminate surface. Cleaning these partitions is very easy. You’ll need a light cleaning agent with a soft piece of brush or cloth to remove low-level stains. But if you’re up against progressively obstinate stains, then you’ll need a strong detergent. Most importantly, you’ll need a cleaner that has acetic acid in it.
Use a delicate brush or fabric to clean before you wash and dry the partitions. Avoid strongly abrasive detergents because they can stain or damage your partitions. It’s not a good idea to hose these partitions down, and retaining an excessive amount of water will make the segments lose their cover. While cleaning them, it’s better if you use a material that is damp and wrung for the most part.
Solid phenolic partitions
Solid phenolic partitions are a lot different than the two materials mentioned above. They’re produced using different layers of paper absorbed in a phenolic resin, which makes it water-resistant. You can even hose these partitions down.
So, your standard cleaning routine should include a delicate fabric and a mix of warm water, and a gentle soap or cleanser.
How to remove hard stains using phenolic partitions:
- Stains that won’t come off, like lipstick or crayon. Using regular cleansers should be enough. Use a degreasing agent, or try a blend of baking soda and water. Consider using a delicate bristled brush instead of a cloth.
- Much harder stains. If, despite your efforts, the stains still won’t come off, refrain from using abrasive detergents. Use a somewhat more dominant cleaner than your delicate cleanser. Look for a restroom cleaner that contains acetic acid so you can remove the stains.
- Spray painting. Sadly, a customary cleaner won’t remove the graffiti. You’ll need a graffiti cleaner for this purpose.
Stainless steel partitions
Stainless steel partitions are the most commonly used partitions because they’re durable. Moreover, they’re non-corrosive because of a slim layer of film on the outside of the metal. Even if this film gets scratched, it will normally change, especially when there’s a lot of oxygen.
Wipe down stainless-steel partitions once a day using a gentle cleanser with warm water. It’s best if the cleanser is diluted ammonia soap. You shouldn’t use fabrics that are too wet when wiping down the segments.
Rinse the partitions with water to wipe away any traces of soap. If a normal cleanser can’t help remove harder stains and scratches, you may try the following:
- Oil or grease stains. Use a mixture of water, kerosene solvent, and cleanser.
- Dirt buildup. Use a metal cleaner that can clean steel surfaces.
- Mineral deposits. You need to use a more abrasive detergent for this, such as Ajax.
Below are the things you need to remember when cleaning these partitions:
- Remember to consistently rub in the same direction of the grain on the surface so you won’t scar the surface.
- You should avoid 2 or three cleaning items: any cleaning item that contains bleach, acid, or alkali (such as toilet bowl cleaners or tile cleaners). These items will demolish the stainless surface, and leave bunches of dark spots on the surface.
- Avoid using steel wool and scrubbing pads.
Just like stainless steel partitions, powder-coated partitions are resistant to rust and extremely durable. They are produced with steel sheets covered with a defensive layer of zinc before being framed and solidified together.
For powder-coated partitions, use a mix of warm water and regular detergent. Your optimal cloth is a sponge or a delicate material. Rinse the partitions with water after you clean so you can remove the detergent completely.
It’s best to apply wax to them over a certain period, as it will keep the smooth surface of the segment. Here are what you should do to clean powder-coated toilet partitions:
- Stubborn dirt. Remove the dirt with a soft fabric or a paper towel.
- Grease spots. Use regular detergent with warm water.
- Spray painting. To remove graffiti, you need to use a graffiti cleaner, specifically for powder-coated partitions. Most graffiti cleaners aren’t for this kind of surface, so you need to be careful when using a cleaner.
Once again, do not use abrasive detergents when cleaning your toilet partitions. They can damage the surface or put scratches on the partitions. What’s worse is that they can fade the paint. Your most logical option is to use delicate cleaners.